Zebra sticker waybills
Requirements
Printer
All printers supported by Zebra Browser Print can be used. We recommend and have tested the following models: ZD230, ZD421, ZD220.
Activation
To enable this feature on your account, navigate to settings in the left navigation pane. In the shipping sub-menu, enable sticker label printing under waybills.
Follow the printer installation guide below to set up your Zebra printer.
Setup and installation
Windows
Download application
Download the Zebra Browser Print application for your Windows operating system:
Connection options
USB: Connect the Zebra label printer to your PC/Mac using a USB cable and power it on. Windows will automatically install the required drivers. No additional driver installation is required.
LAN (if supported): Connect the Zebra label printer to your local network (LAN) using a network cable and power it on. Make sure your network is configured to automatically assign IP addresses (DHCP) or refer to your printer manual for instructions on how to manually configure your printer’s IP address.
Install and run
Once the Zebra Browser Print is downloaded, navigate to the applicable folder and open Browser Print. Click to Run and finish the installation by following the prompts.
Set default device/printer
Open Zebra Browser Print, navigate to "Change" and selected the printer from the drop down menu. Click on "Set" to save. Please ensure your printer stays connected to your computer during this process.
Finalising installation
Once the device/printer has been set, log in to your Bob Go account, navigate to shipments and print a Zebra sticker waybill.
You will be asked to allow “https://www.bobgo.co.za” access to the Zebra printer. Click “Yes” to complete the configuration and print your shipping label.
Print label
After printing your first shipping label, you need to make sure that the alignment of the sticker is correct – in other words, that all the information is visible on the sticker and that nothing is cut off on the sides. If this is not the case, then it will require you to recalibrate the label printer.
Recalibrating the printer
Each model has different steps to perform a quick calibration. In order to confirm the exact steps to calibrate your specific Zebra Printer, search for your model number on Google.
ZD220 and ZD230: Press and hold the "Feed" button until the status light blinks off and on twice, then release. The printer will then print out blank waybills until the calibration process is finished.
GK420d: Hold the green "Feed" button down. First the light on the button will flash once, then it will do a double flash. Let go of the button after the double flash and the printer will start to feed labels forward slowly.
Should you have any issues calibrating, feel free to reach out to our support at support@bobgo.co.za or 012 940 1060 with the model name and they will be sure to provide you with the right steps.
macOS
Download application
Complete the required form and download the Zebra Browser Print application for your macOS operating system:
Connection options
USB: Connect the Zebra label printer to your PC/Mac using a USB cable and power it on. macOS will automatically install the required drivers. No additional driver installation is required.
LAN (if supported): Connect the Zebra label printer to your local network (LAN) using a network cable and power it on. Make sure your network is configured to automatically assign IP addresses (DHCP) or refer to your printer manual for instructions on how to manually configure your printer’s IP address.
Open and run
Once downloaded, open Browser Print and drag the Browser Print icon into your applications folder.
Double-click on applications, and right-click to open Browser Print. It is important to note that you will have to right-click to open Browser Print based on security limitations from macOS.
End User License Agreement
When prompted, accept the “Browser Print End User License Agreement”
Set default device/printer
Open Zebra Browser Print, navigate to "Change" and selected the printer from the drop down menu. Click on "Set" to save. Please ensure your printer stays connected to your computer during this process.
Finalising installation
Once the device/printer has been set, log in to your Bob Go account, navigate to shipments and print a waybill.
Print label
After printing your first shipping label, you need to make sure that the alignment of the sticker is correct – in other words, that all the information is visible on the sticker and that nothing is cut off on the sides. If this is not the case, then it will require you to recalibrate the label printer.
Recalibrating the printer
Each model has different steps to perform a quick calibration. In order to confirm the exact steps to calibrate your specific Zebra Printer, search for your model number on Google.
ZD220 and ZD230: Press and hold the "Feed" button until the status light blinks off and on twice, then release. The printer will then print out blank waybills until the calibration process is finished.
GK420d: Hold the green "Feed" button down. First the light on the button will flash once, then it will do a double flash. Let go of the button after the double flash and the printer will start to feed labels forward slowly.
Should you have any issues calibrating, feel free to reach out to our support at support@bobgo.co.za or 012 940 1060 with the model name and they will be sure to provide you with the right steps.
Smart shipping suggestion: When applying the sticker label to the parcel, use the entire label and not just the inside peel. This inside peel is signed and used as proof of delivery by some of our courier partners.Related Articles
Sticker waybills
Streamline your shipping with sticker waybills With sticker waybills*, shipping has never been easier. Your parcels not only look snazzier, but your fulfillment process speeds up and makes shipping big volumes a breeze. Instead of printing multiple ...PDF sticker waybills
Requirements Printer All PDF sticker printers supporting the set sticker size can be used. We recommend and have tested the Trophy Thermal Printer. Trophy Bob Shop Stickers Outside: 150mm x 102mm Inside peel: 127mm x 84mm Now available from Redfern ...Bulk tools
Bulk tools allow users to perform a range of actions on a batch of selected orders or shipments, significantly increasing operational efficiency and reducing manual workload. To execute a bulk action, choose the specific orders or shipments to which ...Order courier stationery
To order stationery from the couriers, log in to your Bob Go account, go to the Resource hub in the left navigation menu, and select Order courier stationery. Complete the form to place your order.Paperless returns
Please note that this process should be the exception and not the norm. Paperless returns can only be done when booking with The Courier Guy. If your customer is unable to print the Bob Go waybill, then the sender should write the Bob Go waybill ...